Are you looking for Eurosec Pr5208 Rev10 User Manual? You then come off to the right place to get the Eurosec Pr5208 Rev10 User Manual. Read any ebook.

• Contents Introduction.. 1 Display Status Blanking.2 IMPORTANT USER INFORMATION. • Introduction Welcome to the eurosec control panel. Your installation company will have programmed your system to protect your premises to the highest possible standards. Several user programmable options are available that will be covered later in this manual.

Throughout this manual, reference will be made to the Master User Code, the factory set default is 5678. • Display Status Blanking Depending on Control Panel installed, it may be a requirement that the Status (Set or Unset display) of the security system is not displayed. Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset. The bottom line of the display will then be blanked off. • Full Setting the System.

Instrukciya po forme 1 vt map. Two methods are available for Full Set. After checking the premises are secure: Enter a valid User Code followed. * If enabled by the installation engineer.

The exit tone will now sound. Exit the premises via an authorised exit route.

• Pre Exit Check. At the start of the setting procedure, a fault Exit Now!.. Tone will sound if any non exit routes are Zone 3 open. The display will show, for example:- If the fault clears within 20 seconds then the exit tone will begin, if not, the fault tone will continue until a valid User code is entered. • Part Setting the System (using Part 2 or 3). Two other Part Sets may be available for your system. Part 2 is a second set of zones that may be omitted and Part 3 will combine Part 1 and Part 2.

To use Part 2 or 3. Enter a valid User Code followed by 2 or 3.

• Unsetting the System. Enter the premises via an authorised Entry Point.

The entry tone will sound. Proceed to the keypad and enter a valid User Code. Display After an Alarm.

If an alarm occurs when the system is set, the cause of the alarm will be displayed for 10 seconds after you unset the system. • Resetting After an Alarm After an alarm the system needs to be reset. Your installation company will have programmed the reset modes for your system so that it complies with your insurance company and legislation requirements. Your installation company will have informed you as to the type of reset that your system is set for. • If a Master Code Reset has been programmed by the engineer, a higher level of code will be required.

If Alarm Reset has been programmed for Master, then the display will show, for example, each time the User attempts to set!!! • If Anti has been programmed for Alarm Reset, contact the Central Station or Engineer, (as instructed by the Installation Company) and quote the number given by the display. The central station or engineer will give a return Anti-Code (this may contain the (YES) &. • Tamper Resetting With the display showing:-!!!!

Enter a valid User code. The system is now reset. Setting the system with Mains Fail In the event of a short term power cut, where it is known when power will be restored, (e.g. • Enter your User Code again followed. * If enabled by the installation engineer. The exit tone will now sound. Exit the premises via an authorised exit route.

Note: Pressing the (Quick) key during exit will shorten the exit time to 3 seconds. • Re-setting the display after a Mains Fail If the system has been programmed for Any code reset; With the display showing:-!!!! Enter your User code Then press Reset. The display is now reset. • Programming User Codes Up to nine user codes may be programmed on predetermined levels.

User Numbers 1 to 3 Master Level. Allows Set, Part Set, Unset and User Programming Mode. User Numbers 4 to 7 User Level.

Allows Set, Part Set and Unset. User Numbers 8 to 9 Set Only Level. • Press (No). Do You Want to. The display will show:- Program Codes?

9 The display will show:- Press a single digit corresponding to the user number (1 to 9) that you wish to program. The display will show for example:- Code # # # #.

Foto vskritiya zhenschin v morge en. For Perez, who reached last year’s Olympic final but failed to record a throw, it was a memorable triumph and just the second time she had defeated the Croatian following her victory in Lausanne two years ago. The 24-year-old Swede had arrived at this event having won his previous IAAF Diamond League outing in Oslo just three days earlier with 68.36m. Daniel Stahl produced his fifth 68-metre-plus discus throw of the season in an effort to produce a home victory for an Olympic Stadium crowd basking in brilliant sunshine, but fell marginally short as Jamaica’s Fedrick Dacres, who leads this season’s world list with 68.88m, won with a fourth-round effort of 68.36m, his best ever throw outside Jamaica. No doubt for Perkovic – whose marginal foul in the second round annulled an effort that appeared in the 70-metre territory – it will prove a spur to further excellence in the second half of the season. Stahl left his best effort to last but had to settle for second with 68.13m.